ChanServ changed the topic of #msm8937-mainline to: Boot Linux on your MSM8917/37/40 and QM215 mobile! | GitHub: https://github.com/msm89x7-mainline | Logs: https://oftc.irclog.whitequark.org/msm8937-mainline | Bridged to #msm8937-mainline:kde.org on Matrix
<NekoCWD[m]> sdm439 == overclocked msm8937?
<barni2000[m]> almost
<barni2000[m]> there are some difference
<barni2000[m]> * are some more difference
<barni2000[m]> and sdm429 is upgraded 8917
<barni2000[m]> or 4 core 439
<M0xCAFEBABE[m]> <barni2000[m]> "there are some difference" <- like, 28nm -> 12nm DSI, pm8937 -> pm8953, pmi89xx -> pmi632
<barni2000[m]> then its like an underclocked sdm632
<barni2000[m]> pmi can be anything
<barni2000[m]> and pm also changeable
<M0xCAFEBABE[m]> barni2000[m]: no, still sdm632 is based on msm8953...
<barni2000[m]> in software yes
<M0xCAFEBABE[m]> at least sdm632 supports usb3 but sdm439 is still usb2
<barni2000[m]> sdm632 is an overclocked msm8953 mostly used with pmi632 and pm8953
<barni2000[m]> btw these SoCs are very similar is in half way 8937 is between 8916 and 8953
<M0xCAFEBABE[m]> <barni2000[m]> "and sdm429 is upgraded 8917" <- qm215 and qcm2150 is upgraded 8917, sdm429 is trimmed down sdm439
<barni2000[m]> * btw these SoCs are very similar 8937 is in half way is between 8916 and 8953
<M0xCAFEBABE[m]> barni2000[m]: yeah...
<barni2000[m]> 8940 much closer to 8953 because it is using ipa v2.6
<NekoCWD[m]> I want to by android-wear watches to run pmos on it. Looking to https://wiki.postmarketos.org/wiki/Mobvoi_Ticwatch_E3_(mobvoi-ricefish)
<M0xCAFEBABE[m]> do they allow bootloader unlock
<M0xCAFEBABE[m]> & what can you do after you run pmos on it...
<M0xCAFEBABE[m]> * you do on it after you
<M0xCAFEBABE[m]> * what can you do on it after you run pmos on it...
<NekoCWD[m]> idk, but it will be cool
<NekoCWD[m]> Maybe i will write some gtk watchface, idk
<Danct12[m]> <NekoCWD[m]> "idk, but it will be cool" <- this
<Danct12[m]> it means you can go around and tell people that your watch runs pmos btw
ungeskriptet_ has joined #msm8937-mainline
ungeskriptet has quit [Ping timeout: 480 seconds]
ungeskriptet_ is now known as ungeskriptet
<barni2000[m]> <NekoCWD[m]> "I want to by android-wear..." <- So expensive for an sdm429
<NekoCWD[m]> <barni2000[m]> "So expensive for an sdm429" <- Yeah, that's only thing that stops me :sad:
<NekoCWD[m]> barni 2000 Don't connect prada to Quick Charge charger. I've connected my and sub board seems to be broken 😿
<NekoCWD[m]> s/barni/barni2000/, s/2000//
<Danct12[m]> blown fuse?
<NekoCWD[m]> ```usb usb3-port2: over-current condition```
<NekoCWD[m]> Overcurrent, i think it's not a fuse
<NekoCWD[m]> Hehe, just add more power and problem will fix itself 😈
<NekoCWD[m]> I think to just remove all qc components (as on ali replacement)
<NekoCWD[m]> It works (red led blinking)
<barni2000[m]> I had same issues on my Redmi Note 3 years ago with cheap quick charge adapter
<barni2000[m]> It even killed one of my SBC
<barni2000[m]> Wrong adapters can do over voltage
<NekoCWD[m]> Yey! My prada works. It booted to lk2nd. Nice
<NekoCWD[m]> Fuck chinesium chargers
<barni2000[m]> There a some diodes what blown on over voltage they can be removed but on long term you should replace them
<barni2000[m]> For next time
<NekoCWD[m]> <NekoCWD[m]> "image.png" <- I've bought replacement
<NekoCWD[m]> I think i don't need qc on it
<barni2000[m]> Replacements are missing those diodes so next time your MB will blown
<NekoCWD[m]> That one was shorted. Replacement has this diode
<NekoCWD[m]> Oh, thats not a diode
<NekoCWD[m]> Lol
<barni2000[m]> just a jumper
<barni2000[m]> and a capacitor
<NekoCWD[m]> That's bad. i have a diode instead of jumper on original board
<NekoCWD[m]> What about modem? Will it work on prada if i just set it as enabled?
<barni2000[m]> it could work but maybe some nodes need to be defined idk
<NekoCWD[m]> barni2000[m]: mpss mem need size, but in general it will work?
<barni2000[m]> ig
<barni2000[m]> you will need to install some package on userspace msm-modem, rmtfs, q6voiced, maybe tqftpserv is not need for prada
<barni2000[m]> 8937 modem should be easier to enable then 8940 modem
<barni2000[m]> my issue is how to define the memory parts
<NekoCWD[m]> What' s wrong with it?
<barni2000[m]> i have not find out how it should be defined
<NekoCWD[m]> ```[ 20.182280] qcom-q6v5-mss 4080000.remoteproc: PBL boot timed out```
<barni2000[m]> iirc my issue was i have not find the memory regions at downstream