pabs has quit [Quit: Don't rest until all the world is paved in moss and greenery.]
pabs has joined #linux-sunxi
JohnDoe_71Rus has joined #linux-sunxi
Daanct12 has joined #linux-sunxi
apritzel has joined #linux-sunxi
apritzel has quit [Ping timeout: 480 seconds]
vagrantc has quit [Quit: leaving]
bauen1 has quit [Ping timeout: 480 seconds]
hentai has quit [Remote host closed the connection]
Daanct12 has quit [Quit: Quitting]
bauen1 has joined #linux-sunxi
Luke-Jr has joined #linux-sunxi
bauen1 has quit [Ping timeout: 480 seconds]
evgeny_boger has quit [Ping timeout: 480 seconds]
bauen1 has joined #linux-sunxi
bauen1 has quit [Read error: Connection reset by peer]
bauen1_ has joined #linux-sunxi
apritzel has joined #linux-sunxi
cnxsoft has joined #linux-sunxi
DarkNeutrino has joined #linux-sunxi
bauen1_ has quit [Remote host closed the connection]
bauen1 has joined #linux-sunxi
dikiy has joined #linux-sunxi
bauen1 has quit [Remote host closed the connection]
bauen1 has joined #linux-sunxi
cnxsoft has quit []
cnxsoft has joined #linux-sunxi
Rajko has joined #linux-sunxi
rajkosto has quit [Read error: Connection reset by peer]
evgeny_boger has joined #linux-sunxi
bauen1_ has joined #linux-sunxi
bauen1 has quit [Ping timeout: 480 seconds]
Rajko has quit [Read error: Connection reset by peer]
bauen1 has joined #linux-sunxi
bauen1_ has quit [Ping timeout: 480 seconds]
grming has joined #linux-sunxi
bauen1_ has joined #linux-sunxi
bauen1 has quit [Ping timeout: 480 seconds]
JohnDoe_71Rus has quit []
cnxsoft1 has joined #linux-sunxi
cnxsoft has quit [Read error: Connection reset by peer]
bauen1_ has quit [Ping timeout: 480 seconds]
evgeny_boger1 has joined #linux-sunxi
cnxsoft1 has quit [Read error: Connection reset by peer]
evgeny_boger has quit [Ping timeout: 480 seconds]
evgeny_boger1 has quit [Remote host closed the connection]
evgeny_boger has joined #linux-sunxi
cnxsoft has joined #linux-sunxi
bauen1 has joined #linux-sunxi
bauen1 has quit [Remote host closed the connection]
bauen1 has joined #linux-sunxi
aedancullen has quit []
JohnDoe_71Rus has joined #linux-sunxi
JohnDoe_71Rus has quit [Remote host closed the connection]
JohnDoe_71Rus has joined #linux-sunxi
cnxsoft has quit []
hentai has joined #linux-sunxi
hentai has quit [Max SendQ exceeded]
hentai has joined #linux-sunxi
grming has quit [Quit: Konversation terminated!]
DarkNeutrino has quit [Quit: Page closed]
apritzel has quit [Ping timeout: 480 seconds]
JohnDoe_71Rus has quit []
dikiy has quit [Ping timeout: 480 seconds]
vagrantc has joined #linux-sunxi
apritzel has joined #linux-sunxi
ftg has joined #linux-sunxi
grming has joined #linux-sunxi
<jernej>
apritzel: do you know if H616 mmc0 supports 1.8 V mode? you didn't connect any regulator for Zero2 nor for X96 mate. Is this the fact or oversight?
<jernej>
ah, scratch that
<jernej>
1.8 V is used for eMMC
<apritzel>
jernej: the H616 is among the first SoCs where PortF can be switched to 1.8V, internally. Eventually there should be a new regulator expressing that
<apritzel>
I played around with the MMC switching sequence in U-Boot back then, but couldn't get it to work. The card eventually always fell back to 3.3V
<apritzel>
I am not sure if that's due to the Zero2 having a pull-up on the CMD line to *3.3V*
<apritzel>
and I don't have equipment to measure that properly
<apritzel>
jernej: if your question is about the missing vqmcc-supply property: apart from two lonely exceptions I don't see them used on any mmc0 port
<apritzel>
jernej: Vinod asked for the F1C100s USB PHY patches to be split off, do you consider this useful?
<apritzel>
I would at least need the PHY binding patch in the series, to not break the DT bindings check
<apritzel>
jernej: also since you mentioned some unfortunate new dependency (which I don't really see), any suggestions on how to order those patches best?